AgTalk Home
AgTalk Home
Search Forums | Classifieds (96) | Skins | Language
You are logged in as a guest. ( logon | register )

How to set slope on a Spectra laser
View previous thread :: View next thread
   Forums List -> Machinery TalkMessage format
 
Fingers77
Posted 3/13/2014 17:39 (#3751842 - in reply to #3751573)
Subject: RE: How to set slope on a Spectra laser



I checked the owners manual. Yes it can be put into a manual mode for slope work.


First thing to know: With a laser like that the further out of level you go, the more inaccurate it will be. It is rated at 1/8" at a 100' radius. When you tilt the slope of a laser it becomes more and more inaccurate the more you tilt the plane. For pipe work it will probably fine. For tile work, maybe not.


If you have more questions please email me, it can be kinda complicated the first time you do it. I also have contact information for a place in Joliet that has some very good people for explaining this kind of stuff probably better than me. They sell it, I just use them. Good luck.


What you need to do to set the slope:

First set up the laser and let it level itself. It MUST be set on the plane you are going to tilt and square to your line of slope. The indicators (it probably has them on the top or near it) that look like a Less Than Sign (<) MUST be pointed at a RIGHT ANGLE to the slope you want to tilt AND square to the starting point of the slope. I.e. where you want to start the pipe. Shoot that point and set the indicator to a steady beep. You then need to go to the far end of the slope, either the downhill or uphill end point. You must have a final grade. If you are shooting the bottom of the pipe, you must have a start and stop point that are both at final pipe level. You can't shoot the top of one and the bottom if the other.

Go to the end point and hold the stick. DO NOT MOVE THE SENSOR ON THE STICK. Set the laser to manual mode.

Quoting from the manual:



"Using the Manual Mode
Pressing the manual button on the laser or the remote control changes the laser from automatic self-leveling
mode to Manual mode. Manual mode is indicated by the flashing (once every second) red LED 5.
In Manual mode (horizontal), the Y-axis can be sloped by pressing the Up- and Down-Arrow-buttons on the
laser‘s keypad or the remote control. Additionally, the X-axis can be sloped by pressing the Left- and Right-
Arrow-buttons on the remote control.

To resume automatic self-leveling mode, press the manual button again.
Using the Y- or X-Axis Single Slope Mode

To activate the Y-axis single slope mode, press the manual button (1 second) after the up arrow button at the
laser or remote control has been pressed and released. This is indicated by the simultaneously flashing red
5 and green 4 LEDs (once every second).
In Y-axis single slope mode, the Y-axis can be sloped by pressing the Up- and Down-Arrow-buttons on the
laser or the remote control, while the X-axis remains in automatic self leveling mode (e.g. when setting up
sloped ceilings or drive ways).
To activate the X-axis single slope mode, press the manual button (1 second) after the right arrow button at
the remote control has been pressed and released. This is indicated by the simultaneously flashing red 5 and
green 4 LEDs (every 3 seconds).
In X-axis single slope mode, the X-axis can be sloped by pressing the right- and left-Arrow-buttons on the
remote control, while the Y-axis remains in automatic self leveling mode
To resume automatic self-leveling mode, press the manual button again."



So you need to tilt the plane of the laser to find the sensor. Keep tilting the plane of the laser until the laser beeps fast, then steady. When you have a steady beep, you are done. Any point along that plane that the sensor reads a steady beep, it is on plane (grade).



Another Quote from the manual:

"Using the Y-Axis Single Slope Mode
1. Set up the laser over the reference point (A).
2. Look over the rotor to align the laser to the desired direction hub
in the axis that is supposed to be used in automatic self-leveling
mode. Turn the laser on the tripod until it is properly aligned.
3. Attach a receiver to a grade rod. Set the grade rod on the self-leveling
axis direction hub to check the laser’s elevation (B).
Note: Use this HI as a reference for checking the alignment
of the laser after setting the slope for the other axis.
4. Activate the Y-axis single slope mode by pressing the manual button
(1 second) after the up arrow button at the laser or remote control
has been pressed and released.
5. Check the laser’s elevation on the slope axis directly in front of the
laser.
6. Set the grade rod on the slope axis direction hub to adjust the laser’s elevation without changing the height
of the receiver on the grade rod (C).
7. Press the up and down arrow buttons until you get an on-grade reading on the receiver.
8. Recheck the laser’s elevation in automatic self-leveling axis using the HI in step 3 (B).
If the HI has been changed, rotate the laser on the tripod until you get an on-grade reading again. Make sure,
you DON’T change the height of the receiver on the grade rod."



Here is a link to the operating manual for your laser if you do not have one:


http://trl.trimble.com/dscgi/ds.py/Get/File-407208/HV101%20Multi-La...
Top of the page Bottom of the page


Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

(Delete cookies)