|
Franklinton, LA | If you have the correct voltage and amps, you should be able to rip a 1" oak board with a 1 1/2 HP table saw. I have easily ripped a lot of 1" hickory and 1 1/2" oak boards with my 1 1/2 HP, 110-volt table saw.
You might want to check voltage and amps while actually ripping a 1" oak board. Before checking this, I would check to be certain the rip fence is parallel to the saw blade. I assume you have the proper size belt and it is in good condition, the pulleys are properly aliened and in good condition and the belt is properly tensioned. Also, have the blades been recently sharpened? I like to extend the blade life by brushing each side of the board to get rid of the sawdust, dirt, dust and grit.
I prefer a 40-tooth, 10" blade over a 24-tooth. On my table saw the 40-tooth blade will cut faster and give a smoother cut.
Edited by DRester 12/5/2025 20:26
| |
|
- ? for engineers, wood workers, and all around know it all's ;> ) - Paystar500 : 12/5/2025 18:53
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - Busted Piston : 12/5/2025 19:01
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - JohnW : 12/5/2025 19:08
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - Yoosta B : 12/5/2025 19:42
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - scott312 : 12/5/2025 19:44
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - Haleiwa : 12/5/2025 19:49
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - DRester : 12/5/2025 19:53
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - ManiaPlus : 12/5/2025 21:50
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - Iowajim : 12/5/2025 21:53
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - WildBuckwheat : 12/5/2025 22:10
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - WayneWKY : 12/5/2025 22:43
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - rosiesdad : 12/6/2025 07:03
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - Hick : 12/6/2025 08:24
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - HuskerJ : 12/6/2025 09:17
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - DieselDennis : 12/6/2025 09:18
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - chisel : 12/6/2025 10:58
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - tommyw-5088 : 12/6/2025 14:58
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - DRester : 12/6/2025 15:07
- RE: ? for engineers, wood workers, and all around know it all's ;> ) - 150pilot : 12/6/2025 20:07
|
? for engineers, wood workers, and all around know it all's ;> )
