|
West Central Iowa | Part numbers for above diagram 1 1 NSS NOT SERVICED SEPARATELY BODY - valve
2 1 G108675 SPRING SPRING - 63.9 mm long, control, flow, Used in Transmissions prior to S/N AJB0014383., Part of flow control adjustment kit, P/N 1343791C2
2 1 1980066C1 SPRING SPRING - 67.7 mm long, control, flow, transmission serial number AJB0014383 and after
3 1 1957861C1 WASHER WASHER - retainer
4 1 1957862C1 PISTON PISTON - load check
5 1 1957859C1 SNAP RING RING - snap
6 1 71121 SEAL WIPER - piston
7 1 G110391 O-RING O-RING - piston
8 1 86529630 PLUG PLUG, Hex Soc, 3/8"-24 ORB, Assembly, Includes Ref. 9
9 1 218-5002 O-RING O-Ring, 3-1, .301" ID x .064" Thk
1 NSS NOT SERVICED SEPARATELY SPOOL ASSEMBLY - main, order 1980311C1, Includes: Ref. 10 - 17
10 1 NSS NOT SERVICED SEPARATELY SPOOL - main
11 1 1543364C1 STUD STUD - detent, Replaces: G108910
12 1 G108913 SPRING CUP RETAINER - spring, outer
13 1 G108914 SPRING CUP RETAINER - spring, inner
14 1 G108915 SPRING SPRING - centering
15 1 G108630 HOLDER RETAINER - o-ring
16 1 G110391 O-RING O-RING - spool
17 1 237-6002 O-RING O-Ring, 2-1, .239" ID x .064" Thk, Retainer
1 G108633 CHECK VALVE CHECK ASSEMBLY - load, signal, if used, Includes: Ref. 18 - 26
18 1 86632547 PLUG PLUG, Hex Soc, 5/16"-24 ORB
19 1 NSS NOT SERVICED SEPARATELY BODY - check, Replaces: G108615
20 1 G108938 VALVE SPRING SPRING - load
21 1 G108723 RING RING - backup
22 1 G108724 BACK-UP RING RING - backup
23 1 211-256 BALL BALL - steel, 7/32 inch diameter
25 1 238-6012 O-RING O-RING, -012, 90 Duro, .364" ID x .070" Thk
26 1 238-6015 O-RING O-RING, -015, 90 Duro, .551" ID x .070" Thk
1 1346310C2 SLEEVE VALVE SLEEVE ASSEMBLY - flow, Replaces: G108962 and 1994676C1, Includes: Ref. 27 - 31
27 1 NSS NOT SERVICED SEPARATELY SLEEVE - control
28 1 NSS NOT SERVICED SEPARATELY SPOOL - control
29 1 G108901 PLUG PLUG - spool
30 1 238-6012 O-RING O-RING, -012, 90 Duro, .364" ID x .070" Thk
31 1 L31750 CIRCLIP Ring, Snap, 0.562", Int, #56
1 1343735C2 VALVE CONTROL ASSEMBLY - flow adjustment, Replaces: 1980277C1, 1343791C1, and 1343735C1, Includes: Ref. 32 - 41, Part of flow control adjustment kit, P/N 1343791C2
32 1 1980302C2 ROD ROD ASSEMBLY - adjusting, flow, Replaces: 1971861C1 and 1980302C1, Includes: Ref. 33
33 1 138-56 LOCK PIN PIN, 1/8" x 11/16", Slotted
34 1 G101066 SEAL SEAL - oil
35 1 1980226C1 PLUG PLUG - adjusting, Replaces: 1971859C1
36 1 1980227C1 PLUG NUT - compression, Replaces: G108725
37 1 G108956 RACE RACE - bearing, thin
38 1 G108957 RACE RACE - bearing. thick
39 1 237-6010 O-RING O-RING, 10-1, 90 Duro, .755" ID x .097" Thk
40 5 1986628C1 O-RING O-RING - 3/8 ID x 9/16 inch
41 1 F13537 BEARING BEARING - pin
1 1542563C1 CHECK VALVE CHECK ASSEMBLY - load, if used, Includes: Ref. 42 - 46
42 1 NSS NOT SERVICED SEPARATELY BODY - check
43 1 1543329C1 VALVE POPPET PLUG - poppet, load check
44 1 G108723 RING RING - backup
45 1 238-6015 O-RING O-RING, -015, 90 Duro, .551" ID x .070" Thk
46 1 1994581C1 SPRING SPRING - load check
1 1343791C2 SET OF PARTS KIT - flow control adjustment, includes 1343735C2 control assembly, plus instructions (replaces
tch:
Edited by mailman13 3/17/2010 21:38
Attachments
----------------
 magnum first valve.txt (3KB - 757 downloads)
| |
|
Another Magnum question for Redwrench
