AgTalk Home
AgTalk Home
Search Forums | Classifieds (7) | Skins | Language
You are logged in as a guest. ( logon | register )

NMEA Trimble to John Deere
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forums List -> Precision TalkMessage format
 
meyer
Posted 12/21/2011 15:41 (#2116429)
Subject: NMEA Trimble to John Deere


Bluffton, Ohio
Is there a way to change the decimal output in a Trimble display to a John Deere display ? If so what display ?

Thanks

Or will a newer Deere display take 8 decimal places ?

Edited by meyer 12/21/2011 15:45
Top of the page Bottom of the page
torn
Posted 12/21/2011 16:09 (#2116459 - in reply to #2116429)
Subject: Re: NMEA Trimble to John Deere


roaming
You need an EZ-Guide 250 or 500, an FM750, an FM1000 (I think), or a NavII controller. The 162/252/262 receiver cannot be configured to output less than 8 decimal places.

I think the new 2630 MIGHT be able to take 8. Not sure.
Top of the page Bottom of the page
jdamsman
Posted 12/21/2011 16:48 (#2116496 - in reply to #2116429)
Subject: RE: NMEA Trimble to John Deere


se sd
the 2630 will not accept 8 decimals. just tried on a nh with a 262. waiting for the nh guy come and hookup to the nav controller to change.
Top of the page Bottom of the page
meyer
Posted 12/21/2011 18:41 (#2116708 - in reply to #2116429)
Subject: Re: NMEA Trimble to John Deere


Bluffton, Ohio
I am using a EZ guide 500 on RTK and can not change it to 6 and still be able to use RTK on the 500. Will the 750 or FM 1000 allow this ?


I am using the serial port for Ohio CORS will the aux port work?

Edited by meyer 12/21/2011 18:45
Top of the page Bottom of the page
Jason Hinson
Posted 12/21/2011 19:37 (#2116855 - in reply to #2116708)
Subject: Re: NMEA Trimble to John Deere



Kingston, Iowa
2 seasons ago I used my 500 on Iowa Cors to output RTK to a 2600 Display. I believe I used the aux port to get it out, as I was running an EZ Steer with it too.
Top of the page Bottom of the page
softtail
Posted 12/21/2011 19:54 (#2116907 - in reply to #2116855)
Subject: Re: NMEA Trimble to John Deere


SWMN
a 750 you can change to 6 to 8 places
Top of the page Bottom of the page
meyer
Posted 12/21/2011 20:24 (#2116989 - in reply to #2116855)
Subject: Re: NMEA Trimble to John Deere


Bluffton, Ohio
So I should be able to use the serial port as I am now with 8 decimal places. Buy an aux port cable 4001968 ? and then in the setup of the aux port change the decimal places to 6 and turn on the strings I need for my brown box display for yeild mapping. I thought you could only use one port at a time. Jason do you have a part number for the cable you used ?

Thanks
Top of the page Bottom of the page
Jason Hinson
Posted 12/21/2011 20:49 (#2117066 - in reply to #2116989)
Subject: Re: NMEA Trimble to John Deere



Kingston, Iowa
I'll take a look tomorrow when I get to the shop. I do remember it was an expensive one, around $300.

Edited by Jason Hinson 12/21/2011 20:50
Top of the page Bottom of the page
meyer
Posted 12/21/2011 21:19 (#2117188 - in reply to #2116989)
Subject: Re: NMEA Trimble to John Deere


Bluffton, Ohio
Thanks I think I found it 63076 anyone have a used one ???
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

(Delete all cookies set by this site)